Hyundai Sonata: Engine Oil Repair procedures - Lubrication System - Engine Mechanical SystemHyundai Sonata: Engine Oil Repair procedures

Replacement
   
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Exercise caution in order to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.
In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.
1.
Drain the engine oil.
(1)
Remove the oil filler cap.
(2)
Remove the oil drain plug, and drain the oil into a container.

2.
Remove the oil filter (A) with the SST (09263-2E000, the oil filter wrench).
(1)
Remove the oil filter.

(2)
Check and clean the oil filter installation surface.
(3)
Check the part number of the new oil filter is as same as old one.
(4)
Apply clean engine oil to the gasket of a new oil filter.
(5)
Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.
(6)
Tighten it with the torque below.

Tightening torque :
11.8 ~ 15.7N.m (1.2 ~ 1.6kgf.m, 8.7 ~ 11.6lb-ft)

3.
Refill with engine oil.
(1)
Clean and install the oil drain plug with a new gasket.

Tightening torque :
34.3 ~ 44.1N.m (3.5 ~ 4.5kgf.m, 25.3 ~ 32.5lb-ft)

(2)
Fill with fresh engine oil.

Capacity
Total : 4.6 ~ 4.9L (1.21 ~ 1.29 U.S.gal., 4.86 ~ 5.17 U.S.qt., 4.04 ~ 4.30 lmp.qt.)
Oil pan : 4.2 L (1.10 U.S.gal., 4.43 U.S.qt., 1.10 lmp.qt.)
Drain and refill in cluding oil filter :
4.5 L (1.18 U.S.gal., 4.75 U.S.qt., 3.95 lmp.qt.)

(3)
Install the oil filler cap.
4.
Start engine and check for oil leaks.
5.
Recheck the engine oil level.
Inspection
Engine Oil
1.
Check the engine oil quality.
Check the oil deterioration, entry of water, discoloring of thinning.
If the quality is visibly poor, replace the oil.
2.
Check the engine oil level.
After warning up the engine and then 5 minutes after the engine stop, oil level should be between the "L" and "F" marks in the dipstick.
If low, check for leakage and add oil up to the "F" mark.
   
Do not fill with engine oil above the "F" mark.
Selection Of Engine Oil
Recommendation
ACEA A5 or above
(If not available, API SL, ILSAC GF-3, ACEA A3 can be used.)
Supplier
Product
SK
ZIC LD5W-30
Chevron
KIXX G1 LL
Total
QUARTZ HKS G-310 
QUARTZ INEO MC3 5W-30
Shell
HELIX ULTRA AH-E 5W-30
Fuchs
TITAN SUPERSYN LONG LIFE 5W-30/40

   
For best performance and maximum protection of all types of operation, select only those lubricants which :
1.
Satisfy the requirement of the ACEA classification.
2.
Have proper SAE grade number for expected ambient temperature range.
3.
Lubricants that do not have both an SAE grade number and ACEA service classification on the container should not be used.
    Oil Pump Components and Components Location
    Components 1.  Timing chain cover2.  Inner rotor3.  Outer rotor4.  Pump cover ...

    See also:

    Troubleshooting
    Troubleshooting Trouble SymptomProbable CauseRemedyExcessive play in steeringLoose U-joint boltRetighten or replace as necessaryLoose yoke plugRetightenLoose steering gear mounting boltsRetighten ...

    Fuel Pump. Repair procedures
    Removal 1. Release the residual pressure in fuel line (Refer to “Release Residual Pressure in Fuel Line” in this group). 2. Remove th ...

    CVVT Oil Control Valve (OCV) Repair procedures
    Inspection 1. Turn the ignition switch OFF. 2. Disconnect the OCV connector. 3. Measure resistance between the OCV terminals 1 and 2. 4. Check that the resistance is within the specifi ...