Hyundai Sonata: Repair procedures - Lane Departure Warning System (LDWS) - Body Electrical SystemHyundai Sonata: Repair procedures

Service Point Target Auto Calibration (SPTAC)
This procedure provides a way to calibrate the camera by having the service technician align the car to a well lit simulated straight road target; preferably wall mounted.
The LDWS camera will have a "System Out of Calibration" DTC set if not operating within specified tolerances.
The LDWS will be supplied for field service replacement with the "System Calibration Requried / Variant Coding Error" DTC set if it is a replacement part delivered directly from supplier manufacturing.
1.
Guidelines for Selecting a Suitable Target
In order for LDWS Service Calibration-Static routine to complete successfully, the following conditions are required:
A.
Target (SST : 09890-3V100) surface must be perpendicular to the camera in both horizontal and vertical orientation to maintain maximum of 1° roll.
B.
Target to be mounted to rigid backer material to maintain flatness requirements.
C.
Target must have reflective (not faded or poorly painted) markings not to represent lane features.
D.
Target to be 30cm wide by 100cm tall.
E.
Mounting area must NOT have cross hatch patterns or textual markings near the target.
F.
Target should be well lit for optimal performance using non-fluctuating illumination. There shall be no continuous shadows cast on the target.

2.
Service Point Target Auto Calibration Procedure
(1)
Check of vehicle toe-in and tire pressure levels to ensure proper alignment of the camera to the "world” before proceeding with calibration is suggested. The vehicle is to be at nominal production loading capacity when the calibration routine is running.
(2)
Windscreen must be clean and serigraphy checked so that there is no blockage of the camera.
(3)
Service technician connects the diagnostic connector and starts the vehicle. The camera module should not be activated by pressing the switch.
(4)
The service calibration routine may not run correctly if any system level fault is active.
(5)
If working with a replacement ECU: the service technician initiates the SPTAC Reset configuration.
(6)
Service technician either aligns the vehicle to the target or the target to the vehicle.
A.
Bottom of the target is to be 90cm ±2cm from the ground and aligned with the camera lens horizontal axis.
B.
The target is placed along the vehicle’s longitudinal axis (centerline) within ±5cm of target center.
C.
The calibration target has to be placed at the 2.7m distance from the front wheel center (1.74m distance from the bumper)

(7)
Technician ensures target placement location and check the "OK" message on the diagnostic tool (GDS).
(8)
Clear the all of the DTCs.
(9)
IGN off and on.
Drive Test
   
May not activate normally in case of the following conditions.
-
In case lane is not visible due to glare or heavy rain.
-
In case the road is covered with snow.
-
In case puddle on the road surface reflects street light or head light from oncoming vehicle.
-
In case of blocking object such as sidewalk on the side of the road.
-
In case of there is trace of more than one lane due to road repair.
-
In case of distance with vehicle in front is very short.
-
Be sure to run drive test to check normal operation after performing optical angle test.
-
Drive on straight line road (longer than 500m) 2 white or yellow lane marks at speed over 60Km/h, and check when the alert is activated as you intentionally steer close to the lane mark.
-
LDWS operates normally if the lane mark segment space is less than 8m.
-
LDWS activates at vehicle speed above 60Km/h.
-
Perform drive test on car-only road or on a highway.
    Description and Operation
    Description Block Diagram LDWS is Composed of Below Units NoItemFunctionPosition1LDWS UNIT 1. Lane Departure Warning System (LDWS) : Detects drive lane in front and engages warning function i ...

    See also:

    Roof Side Molding Repair procedures
    Replacement     • Put on gloves to protect your hands.     • When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with pr ...

    ESP OFF Switch Repair procedures
    Inspection 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the crash pad side switch assembly. 3. Check the continuity between the switch terminals as ...

    Components and Components Location
    Components (1) 1. Crash pad assembly2. Crash pad side cover [LH]3. Crash pad side cover [RH]4. Crash pad lower panel Components (2) 1. Main crash pad assembly2. Side def nozzle [LH]3. Side ...