Hyundai Sonata: Specifications - General Information - Driveshaft and axleHyundai Sonata: Specifications

Specifications
Joint type
Max. permissible angle
Outer
Inner
Outer
Inner
BJ#95
LSJ#95
45°
21°
BJ#104
LSJ#100
45°
21°

Tightening Torques
Item
N.m
kgf.m
Ib.ft
Front
Wheel nut
88.3 ~ 107.9
9.0 ~ 11.0
65.1 ~ 79.6
Drive shaft castle nut
274.6 ~ 294.2
28.0 ~ 30.0
202.5 ~ 217.1
Strut assembly lower mounting bolt
196.1 ~ 215.7
20.0 ~ 22.0
144.7 ~ 159.1 
Hub assembly mounting bolts
78.5 ~ 98.1
8.0 ~ 10.0
57.9 ~ 72.3
Brake caliper mounting bolt
78.5 ~ 98.1
8.0 ~ 10.0
57.9 ~ 72.3
Wheel speed sensor mounting bolt
8.8 ~ 13.7
0.9 ~ 1.4
6.5 ~ 10.1
Brake disc mounting bolt
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Lower ball joint mounting bolt
98.1 ~ 117.7
10.0 ~ 12.0
72.3 ~ 86.8
Tie rod end ball joint nut
34.3 ~ 44.1
3.5 ~ 4.5
25.3 ~ 32.5
Rear
Wheel nut
88.3 ~ 107.9
9.0 ~ 11.0
65.1 ~ 79.6
Shock absorber upper mounting bolt
49.0 ~ 63.7
5.0 ~ 6.5
36.2 ~ 47.0
Shock absorber lower mounting nut
137.3 ~ 156.9
14.0 ~ 16.0
101.3 ~ 115.7
Brake caliper mounting bolt
78.4 ~ 98.0
8.0 ~ 10.0
57.8 ~ 72.3
Wheel speed sensor mounting bolt
8.8 ~ 13.7
0.9 ~ 1.4
6.5 ~ 10.1
Brake disc mounting bolt
4.9 ~ 5.8
0.5 ~ 0.6
3.6 ~ 4.3
Hub assembly mounting bolt
58.8 ~ 68.6
6.0 ~ 7.0
43.4 ~ 50.6
Upper arm mounting bolt & nut
137.3 ~ 156.9
14.0 ~ 16.0
101.3 ~ 115.7
Lower arm mounting bolt & nut
137.3 ~ 156.9
14.0 ~ 16.0
101.3 ~ 115.7
Assist armt mounting bolt & nut
137.3 ~ 156.9
14.0 ~ 16.0
101.3 ~ 115.7
Trailing arm mounting bolt
98.1 ~ 117.7
10.0 ~ 12.0
72.3 ~ 86.7

Lubricants
Engine
Lubricants
Quantity (g)
THETA2.4 GDI
A/T RH
BJ
GRB006N(CVBJ-2)
105 + 10
A/T LH
100 + 10
A/T RH
LSJ(TJ)
VX712(CVTJ-2)
170 + 15
A/T LH
THETA2.0 T-GDI
A/T RH
BJ
GRB006N(CVBJ-2)
135 + 10
A/T LH
A/T RH
LSJ(TJ)
VX712(CVTJ-2)
215 + 15
A/T LH
GAMMA1.6 T-GDI
7DCT
BJ
GRB006N(CVBJ-2)
150 + 10
LSJ(TJ)
VX712(CVTJ-2)
215 + 15

    Special Service Tools
    Special Service Tools Tool(Number and Name)IllustrationUse09495-3K000Band installerInstallation of ear type boot band09495-33000PullerRemoval of spider assembly from a drive shaft.09495-39100Band ...

    See also:

    Blower Motor Repair procedures
    Inspection 1. Connect the battery voltage and check the blower motor rotation. 2. If the blower motor does not operate well, substitute with a known-good blower motor and check for proper oper ...

    CVVT (Continuously Variable Valve Timing) System. Description and Operation
    Description Continuous Variable Valve Timing (CVVT) system advances or retards the valve timing of the intake and exhaust valve in accordance with the ECM control signal which is calculated ...

    Power Seat Control Switch. Repair procedures
    Inspection With the power seat switch in each position, make sure that continuity exists between the terminals below. If continuity is not as specified, replace the power seat switch. A ...