Hyundai Sonata: Temperature Control Actuator Repair procedures - Heater - Heating, Ventilation and Air ConditioningHyundai Sonata: Temperature Control Actuator Repair procedures

Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the temperature control actuator connector.
3.
Verify that the temperature control actuator operates to the cool position when connecting 12V to terminal 3 and grounding terminal 7.
Verify that the temperature control actuator operates to the warm position when connected in reverse.
[ DATC-LH]

1. -
2. -
3. Cool position
4. Sensor (+ 5V)
5. Feedback signal
6. Sensor ground
7. Warm position

[DATC-RH / MTC]

1. -
2. -
3. Warm position
4. Sensor (+ 5V)
5. Feedback signal
6. Sensor ground
7. Cool position

4.
Connect the temperature control actuator connector.
5.
Turn the ignition switch ON.
6.
Check the voltage between terminal 5 and 6.
Specification
[ DATC-LH]
Door Position
Voltage (V)
Error Detecting
Max. cooling
1.2
Low voltage : 0.1V or less
High voltage : 4.9V or more
Max. heating
4

[DATC-RH / MTC]
Door Position
Voltage (V)
Error Detecting
Max. cooling
4
Low voltage : 0.1V or less
High voltage : 4.9V or more
Max. heating
1.2

It will feedback the current position of the actuator to controls.
7.
If the measured voltage is not within specification, substitute with a known-good temperature control actuator and check for proper operation.
8.
Replace the temperature control actuator if it is proved that there is a problem with it.
Diagnosis With GDS
1.
The heating, ventilation and air conditioning can be quickly diagnosed failed parts with vehicle diagnostic system (GDS).
? The diagnostic system (GDS) provides the following information.
(1) Self diagnosis : Checking the failure code (DTC) and display.
(2) Current data : Checking the system input/output data state.
(3) Actuation test : Checking the system operation condition.
(4) Additional function : Other controlling such as he system option and zero point adjustment.
2.
Select the 'Car model' and the system to be checked in order to check the vehicle with the tester.
3.
Select the 'Current data" menu to search the current state of the input/output data.
The input/output data for the sensors corresponding to the Temperature Control Actuator can be checked.

4.
To perform compulsory operation on Temperature Control Actuator input factors, select "ACTUATION TEST".

Replacement
[Driver's side]
1.
Disconnect the negative (-) battery terminal.
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Lower Panel")
3.
Remove the driver's side shower duct (A) after loosening the screw.

4.
Disconnect the connector (A) and then remove the driver's side temperature control actuator (B) after loosening the mounting screws.

5.
Install in the reverse order of removal.
[Passenger's side]
1.
Disconnect the negative (-) battery terminal.
2.
Remove the glove box housing.
(Refer to Body - "Glove Box Housing")
3.
Remove the passenger's side shower duct (A) after loosening the screw.

4.
Disconnect the connector (A) and then remove the passenger's side temperature control actuator (B) after loosening the mounting screws.

5.
Install in the reverse order of removal.
    Temperature Control Actuator Description and Operation
    Description The temperature control actuator is located at the heater unit. It regulates the temperature by the procedure as follows. The signal from the control unit adjusts the position of the ...

    Mode Control Actuator Components and Components Location
    Components Location 1. Mode control actuator ...

    See also:

    Power windows
    The ignition switch must be in the ON position for power windows to operate. Each door has a power window switch that controls the door's window. The driver has a power window lock switch whic ...

    Temperature control
    Type A Type B The temperature will increase to the maximum by turning the knob to the right. The temperature will decrease to the minimum by turning the knob to the left. When turning the ...

    Tire and loading information label
    The label located on the driver's door sill gives the original tire size, cold tire pressures recommended for your vehicle, the number of people that can be in your vehicle and veh ...