Hyundai Sonata: Interior Trim. Repair procedures - Interior - Body (Interior and Exterior)Hyundai Sonata: Interior Trim. Repair procedures

Replacement

Front Pillar Trim Replacement
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the front pillar trim (A).
2.
Installation is the reverse of removal.
•
Replace any damage clips.
Center Pillar Trim Replacement
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the front door scuff trim and rear door scuff trim.
2.
Using a screwdriver or remover, remove the seat belt lower anchor (A).
3.
Remove the center pillar lower trim (A).
4.
After loosening the mounting screws, then remove the center pillar upper trim (A).
5.
Installation is the reverse of removal.
•
Replace any damaged clips.
Rear Pillar Trim Replacement
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear pillar trim (A).
2.
Installation is the reverse of removal.
•
Replace any damaged clips.
Door Scuff Trim Replacement
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the door scuff trim (A).
[Front]

[Rear]
2.
Installation is the reverse of removal.
•
Replace any damaged clips.
Cowl Side Trim Replacement
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the front door scuff trim.
2.
Remove the hood latch release handle.
(Refer to the BD group - "Hood")
3.
Detach the clip, then remove the cowl side trim (A).
4.
Installation is the reverse of removal.
•
Replace any damaged clips.
Package Tray Trim Replacement
1.
Remove the rear seat assembly.
(Refer to the BD group - "Rear Seat")
2.
After loosening the mounting bolt, then remove the rear seat belt lower anchor (A).
[LH,RH]
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

[Center]
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

3.
Remove the rear pillar trim (A).
4.
After loosening the mounting screws, then remove the package tray trim (A).
5.
Installation is the reverse of removal.

    Interior Trim. Components and Components Location
    Components 1. Front pillar trim 2. Center pillar upper trim 3. Center pillar lower trim 4. Rear pillar trim 5. Cowl side trim 6. Front door scuff trim 7. ...

    Trunk Trim. Repair procedures
    Replacement • Put on gloves to protect your hands. • ...

    See also:

    Clutch Pedal. Repair procedures
    Removal Do not spill brake fluid on the vehicle; it may damage the paint if brake fluid does contact the paint, wash it off im ...

    Battery. Repair procedures
    Removal and Installation 1. Disconnect the terminals from the battery. Tightening torque : (+) terminal (A) : 7.8 ~ 9.8N.m (0.8 ~ 1.0kgf. ...

    For best battery service
    Keep the battery securely mounted. Keep the battery top clean and dry. Keep the terminals and connections clean, tight, and coated with petroleum jelly or terminal grease. Rinse any sp ...