Hyundai Sonata: Rear Hub - Carrier Repair procedures - Rear Axle Assembly - Driveshaft and axleHyundai Sonata: Rear Hub - Carrier Repair procedures

Removal
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the wheel cap (A).

   
Be careful not to damage to the wheel cap (A) when removing the it.
3.
Remove the front wheel and tire (A) from front hub.

Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

   
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
4.
Remove the brake caliper mounting bolts and then place the brake caliper assembly (A) with wire.

Tightening torque :
78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

[General]

[EPB]

5.
Loosen the mount screw and then brake disc (A).

Tightening torque :
4.9 ~ 5.8 N.m (0.5 ~ 0.6 kgf.m, 3.6 ~ 5.3 lb-ft)

6.
Loosen the rear upper arm mounting bolt and then remove the rear upper arm (A).

Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

7.
Disconnect the wheel speed sensor connector (A).

8.
Disconnect the parking cable mounting clip (A), remove the parking cable (B). If EPB type, release the EPB.

9.
Loosen the trailing arm mounting nut (A), and then remove the trailing arm (b).

Tightening torque :
98.1 ~ 117.7 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.8 lb-ft)

10.
Loosen the bolt and then remove the assist arm.

Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

11.
Loosen the lower arm (A) mounting bolts and remove the knuckle assembly (B).

Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

12.
Loosen the hub bearing mounting, and then remove the hub bearing (A) from knuckle.

13.
Install in the reverse order of removal.
    Rear Hub - Carrier Components and Components Location
    Components [EPB Type] 1. Rear carrier assembly2. Dust cover3. Rear hub assembly4. Rear disc brake [General Type] 1. Parking brake assembly2. Rear hub assembly3. Rear disc brake ...

    Rear Hub Assembly Repair procedures
    Replacement 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the wheel cap (A).     Be careful not to damage to the wheel cap (A) when removing the it ...

    See also:

    Special Service Tools
    Special Service Tools Tools (Number and Name) Illustration Use 09200-38001 Engine support fixture Removal and in ...

    Components and Components Location
    Components 1. Driver Airbag (DAB)2. Passenger Airbag (PAB)3. Knee Airbag (KAB)4. Curtain Airbag (CAB)5. Side Airbag (SAB) Components Location Supplemental Restraint System Control Module (SR ...

    Oil Level Gauge & Pipe Repair procedures
    Removal and Installation 1. Remove the oil lever gauge (A). Tightening torque: 9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft) 2. Install in the reverse order of removal. ...