Hyundai Sonata: Rear Lower Arm Repair procedures - Rear Suspension System - Suspension SystemHyundai Sonata: Rear Lower Arm Repair procedures

Removal
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the wheel cap (A).

   
Be careful not to damage to the wheel cap (A) when removing the it.
3.
Remove the front wheel and tire (A) from front hub.

Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

   
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).
4.
Remove the rear lower arm protector.

5.
Loosen the lower arm (A) mounting bolt and nut. And then remove the lower arm form the rear carrier.

Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

   
Set up the transmission jack under the lower arm in order to remove the shock absorber in no-load condition .
Record the position of the alignment marks before removing the rear lower arm to keep from tightening the bolt and washer to the wrong position or the wrong direction.
6.
Loosen the mounting bolt and nut. And then separate the shock absorber from the lower arm.

Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)

   
Set up the transmission jack under the lower arm in order to remove the shock absorber in no-load condition .
Record the position of the alignment marks before removing the rear lower arm to keep from tightening the bolt and washer to the wrong position or the wrong direction.
7.
Loosen the bolt & nut and then remove the rear lower arm (A) from the sub frame.

Tightening torque :
107.9 ~ 117.7 N.m (11.0 ~ 12.0 Kgf.m, 79.6 ~ 86.8 lb-ft)

   
Set up the transmission jack under the lower arm in order to remove the shock absorber in no-load condition .
Record the position of the alignment marks before removing the rear lower arm to keep from tightening the bolt and washer to the wrong position or the wrong direction.
8.
Loosen the bolt & nut and then remove the rear lower arm (A) from the sub frame.

Tightening torque :
107.9 ~ 117.7 N.m (11.0 ~ 12.0 Kgf.m, 79.6 ~ 86.8 lb-ft)

Installation
1.
Installation is the reverse of removal.
   
Install the component with the specified torques.
When installing the bolt, install the lower arm in no-load condition by using the transmission jack.
2.
Check the alignment.
(Refer to Tires/Wheels - "Alignment")
Inspection
1.
Check the bushing for wear and deterioration.
2.
Check the rear lower arm for deformation.
3.
Check for all bolts and nut.
4.
Check the cracks or the cutting of the lower .
    Rear Upper Arm Repair procedures
    Replacement 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the wheel cap (A).     Be careful not to damage to the wheel cap (A) when removing the it ...

    Rear Assist Arm Repair procedures
    Replacement 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the wheel cap (A).     Be careful not to damage to the wheel cap (A) when removing the it ...

    See also:

    Description and Operation
    Description The charging system included a battery, an alternator with a built-in regulator, and the charging indicator light and wire. The Alternator has eight built-in diodes, each rectifying AC ...

    Description and Operation
    Warning Lamp Activation Warning Lamp Behavior after Ignition On As soon as the operating voltage is applied to the SRSCM ignition input, the SRSCM activates the warning lamp for a LED lamp c ...

    Rear Seat Back Cover Components and Components Location
    Component Location 1. Rear seat back cover [LH]2. Rear seat back cover [RH] ...