Hyundai Sonata: Rear Seat Back Cover Repair procedures - Rear Seat - Body (Interior and Exterior)Hyundai Sonata: Rear Seat Back Cover Repair procedures

Replacement
[LH]
   
Put on gloves to protect your hands.
   
When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
Take care not to bend or scratch the trim and panels.
1.
Remove the rear seat back assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Remove the rear seat headrest (A).

   
1)
Push the LH headrest guide locking button (2).
2)
Insert a pin into the hole of the RH headrest guide and push the hidden lock plate (3).
3)
Remove the rear seat headrest (A).
3.
Using a screwdriver or remover, remove the rear seat back cover (A).

4.
Pull out the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

5.
After removing both the clips and velcro tape on the rear of seat back and remove the seat back cover (A).

6.
Install in the reverse order of removal.
   
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the clips (A).
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

[RH]
   
Put on gloves to protect your hands.
   
When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
Take care not to bend or scratch the trim and panels.
1.
Remove the rear seat back assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Remove the rear seat back armrest.
(Refer to Rear Seat - "Rear Seat ")
3.
Remove the rear seat headrest (A).

   
1)
Push the LH headrest guide locking button (2).
2)
Insert a pin into the hole of the RH headrest guide and push the hidden lock plate (3).
3)
Remove the rear seat headrest (A).
4.
Using a screwdriver or remover, remove the rear seat back cover (A).

5.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

6.
After removing both the clips and velcro tape (A) on the rear of seat back and remove the seat back cover (B).

7.
Install in the reverse order of removal.
   
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the clips (A).
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

    Rear Seat Back Cover Components and Components Location
    Component Location 1. Rear seat back cover [LH]2. Rear seat back cover [RH] ...

    Rear Seat Cushion Cover Components and Components Location
    Component Location 1. Rear seat cushion cover ...

    See also:

    Seat Heater Switch. Schematic Diagrams
    Circuit Diagram ...

    Fuel Pump Control Module (FPCM) Schematic Diagrams
    Circuit Diagram Fuel Pressure Control Module (FPCM) Terminal And Input/Output signal FPCM Terminal Function Pin No.DescriptionConnected to1Fuel sender ground Fuel Pump 2Fuel pressure sensor (FPS) ...

    Crash Pad Lower Panel Repair procedures
    Replacement     • Put on gloves to protect your hands.     • When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with pr ...