Hyundai Sonata: Specifications - General Information - Driveshaft and axleHyundai Sonata: Specifications

Specification

Engine
 T/M
 Joint type
 Max. permissible angle
Outer
 Inner
 Outer
 Inner
Gasoline 2.0
 M/T
 BJ#95
 TJ#95
 43°
 21°
A/T
 BJ#95
 TJ#95
 43°
 21°
Gasoline 2.4
 M/T
 BJ#95
 TJ#95
 43°
 21°
A/T
 BJ#95
 TJ#95
 43°
 21°

Tightening Torque
Item
 N.m
 kgf.m
 Ib.ft
Front
 Wheel nut
 88.2 ~ 107.8
 9.0 ~ 11.0
 65.0 ~ 79.5
Drive shaft castle nut
 215.7 ~ 254.9
 22.0 ~ 26.0
 159.1 ~ 188.0
Strut assembly lower mounting bolt
 137.2 ~ 156.9
 14.0 ~ 16.0
 101.2 ~ 115.7
Brake caliper mounting bolt
 78.4 ~ 98.0
 8.0 ~ 10.0
 57.8 ~ 72.3
Wheel speed sensor mounting bolt
 6.8 ~ 10.7
 0.7 ~ 1.1
 5.0 ~ 7.9
Brake disc mounting bolt
 4.9 ~ 5.8
 0.5 ~ 0.6
 3.6 ~ 4.3
Lower ball joint mounting bolt
 98.0 ~ 117.6
 10.0 ~ 12.0
 72.3 ~ 86.7
Tie rod end ball joint nut
 34.3 ~ 44.0
 3.5 ~ 4.5
 25.3 ~ 32.5
Rear
 Wheel nut
 88.2 ~ 107.8
 9.0 ~ 11.0
 65.0 ~ 79.5
Shock absorber upper mounting bolt
 137.2 ~ 156.9
 14.0 ~ 16.0
 101.2 ~ 115.7
Shock absorber lower mounting nut
 137.2 ~ 156.9
 14.0 ~ 16.0
 101.2 ~ 115.7
Brake caliper mounting bolt
 78.4 ~ 98.0
 8.0 ~ 10.0
 57.8 ~ 72.3
Wheel speed sensor mounting bolt
 6.8 ~ 10.7
 0.7 ~ 1.1
 5.0 ~ 7.9
Brake disc mounting bolt
 4.9 ~ 5.8
 0.5 ~ 0.6
 3.6 ~ 4.3
Hub assembly mounting bolt
 78.4 ~ 88.2
 8.0 ~ 9.0
 57.8 ~ 65.0
Upper arm ball joint mounting nut
 137.2 ~ 156.9
 14.0 ~ 16.0
 101.2 ~ 115.7
Lower arm mounting bolt
 137.2 ~ 156.9
 14.0 ~ 16.0
 101.2 ~ 115.7
Assist arm ball joint mounting nut
 44.1 ~ 53.9
 4.5 ~ 5.5
 32.5 ~ 39.7
Trailing arm mounting bolt
 44.1 ~ 53.9
 4.5 ~ 5.5
 32.5 ~ 39.7


Lubricants

Engine
 Lubricants
 Quantity
Gasoline 2.0
 BJ
 GRB006 (UREA)
 105g
TJ
 SH06-VX21(UREA)
 145g
Gasoline 2.4
 BJ
 GRB006 (UREA)
 105g
TJ
 SH06-VX21(UREA)
 145g


    Special Service Tools
    Special tools Tool(Number and Name) Illustration Use 09495-33000 Puller Removal of spider assembly from a drive sha ...

    See also:

    Engine Coolant Temperature Sensor (ECTS) Repair procedures
    Inspection 1. Turn the ignition switch OFF. 2. Remove the ECTS (Refer to "Removal"). 3. After immersing the thermistor of the sensor into engine coolant, measure resistance between the ECT ...

    Alternator. Components and Components Location
    Components 1. Pulley 2. Front bracket 3. Front bearing 4. Bearing cover 5. Bearing cover bolt 6. Rotor 7. Rear bearing 8. Rear bracket 9. Through b ...

    Starter Relay Repair procedures
    Inspection 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the fuse box cover. 3. Remove the starter relay (A). 4. Using an ohmmeter, check that th ...