Hyundai Sonata: Tightening Torque Table Of Standard Parts - General InformationHyundai Sonata: Tightening Torque Table Of Standard Parts

Bolt nominal
diameter (mm)
Pich (mm)
Torque Nm (kg.cm, lb.ft)
Head Mark 4
Head Mark 7
государственная экологическая экспертиза стоимость

M5
0.8
3 ~ 4 (30 ~ 40, 2.2 ~ 2.9)
5 ~ 6 (50 ~ 60, 3.6 ~ 4.3)
M6
1.0
5 ~ 6 (50 ~ 50, 3.6 ~ 4.3)
9 ~ 11 (90 ~ 110, 6.5 ~ 8.0)
M8
1.25
12 ~ 15 (120 ~ 150, 9 ~ 11)
20 ~ 25 (200 ~ 250, 14.5 ~ 18.0 )
M10
1.25
25 ~ 30 (250 ~ 300, 18 ~ 22)
30 ~ 50 (300 ~ 500, 22 ~ 36)
M12
1.25
35 ~ 45 (350 ~ 450, 25 ~ 33)
60 ~ 80 (600 ~ 800, 43 ~ 58)
M14
1.5
75 ~ 85 (750 ~ 850, 54 ~ 61)
120 ~ 140 (1,200 ~ 1,400, 85 ~ 100)
M16
1.5
110 ~ 130 (1,100 ~ 1,300, 80 ~ 94)
180 ~ 210 (1,800 ~ 2,100, 130 ~ 150)
M18
1.5
160 ~ 180 (1,600 ~ 1,800, 116 ~ 130)
260 ~ 300 (2,600 ~ 3,000, 190 ~ 215)
M20
1.5
220 ~ 250 (2,200 ~ 2,500, 160 ~ 180)
360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
M22
1.5
290 ~ 330 (2,900 ~ 3,300, 210 ~ 240)
480 ~ 550 (4,800 ~ 5,500, 350 ~ 400)
M24
1.5
360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
610 ~ 700 (6,100 ~ 7,000, 440 ~ 505)

1.
The torques shown in the table are standard values under the following conditions.
Nuts and bolts are made of galvanized steel bar.
Galvanized plain steel washers are inserted.
All nuts, bolts and plain washers are dry.
2.
The torques shown in the table are not applicable.
When spring washers, toothed washers and the like are inserted.
If plastic parts are fastened.
If self-tapping screws or self-locking nuts are used.
If threads and surfaces are coated with oil.
3.
Reduce the torque values to the indicated percentage of the standard value under the following conditions.
If spring washers are used : 85%
If threads and bearing surfaces are stained with oil : 85%
    Towing
    If the vehicle needs to be towed, call a professional towing service. Never tow vehicle with just a rope or chain. It is very dangerous. Emergency Towing There are three popular method ...

    General Service Information
    Protection Of The Vehicle Always be sure to cover fenders, seats, and floor areas before starting work. The support rod ...

    See also:

    High mounted stop light replacement
    1. Set the front seatback to the upright position and if necessary, slide the front seat forward. 2. Pull up the rear seat cushion. 3. Remove the nuts under the seat connecting each side o ...

    Repair procedures
    Inspection 1. Remove the cowl top cover. (Refer to the wiper) 2. Disconnect the windshield deicer connector (A) from the wiper motor linka ...

    Rocking the vehicle
    If it is necessary to rock the vehicle to free it from snow, sand, or mud, first turn the steering wheel right and left to clear the area around your front wheels. Then, shift back and forth betwe ...