Hyundai Sonata: Instrument Cluster. Repair procedures - Indicators And Gauges - Body Electrical SystemHyundai Sonata: Instrument Cluster. Repair procedures

Inspection

Speedometer
1.
Adjust the pressure of the tires to the specified level.
2.
Drive the vehicle onto a speedometer tester. Use wheel chocks (A) as appropriate.
3.
Check if the speedometer indicator range is within the standard values.
Do not operate the clutch suddenly or increase/ decrease speed rapidly while testing.
Tire wear and tire over or under inflation will increase the indication error.

[Canada - km/h]
Velocity
(km/h)
Tolerance
(km/h)
Velocity
(km/h)
Tolerance
(km/h)
20
+2.2
+0.2
160
+5.5
+2.5
40
+2.3
+0.3
180
+7.3
+3.3
60
+2.5
+0.5
200
+7.5
+3.5
80
+3.2
+0.7
220
+8
+4
100
+4
+1
240
+8.5
+4.5
120
+4.5
+1.5
260
-
140
+5
+2
 
 

[USA - MPH]
Velocity
(MPH)
Tolerance
(MPH)
Velocity
(MPH)
Tolerance
(MPH)
10
+1.5
+0
100
+3.8
+1.3
20
+1.5
+0
120
+5
+2
40
+1.5
+0
140
+6
+3
60
+2.3
+0.3
160
+5.8
+2.8
80
+3.3
+0.8




Tachometer
1.
Connect the GDS to the diagnostic link connector or install a tachometer.
2.
With the engine started, compare the readings of the tester with that of the tachometer. Replace the tachometer if the tolerance is exceeded.
1.
Reversing the connections of the tachometer will damage the transistor and diodes inside.
2.
When removing or installing the tachometer, be careful not to drop it or subject it to severe shock.
Revolution
(rpm)
Tolerance (rpm)
Max 8000rpm
Gasoline
1,000
±100
2,000
±100
3,000
±100
4,000
±100
5,000
±100
6,000
±100
7,000
±100
8,000
±100

Fuel Gauge
1.
Disconnect the fuel sender connector from the fuel sender.
2.
Connect a 3.4 watt, 12V test bulb to terminals 1 and 3 on the wire harness side connector.
3.
Turn the ignition switch to the ON, and then check that the bulb lights up and the fuel gauge needle moves to full.

Main Fuel Gauge Sender
1.
Using an ohmmeter, measure the resistance between terminals 1 and 3 of sender connector (A) at each float level.

2.
Also check that the resistance changes smoothly when the float is moved from "E" to "F"
Position
Liter (ℓ)
U.S.gal.
Resistance (Ω)
Sender (E)
5
1.32
200 ± 2Ω
Warning lamp ON
8.5
2.24
170 ± 2Ω
1/2
36
9.51
72.2 ± 2Ω
Sender (F)
68
17.96
8 ± 2Ω

3.
If the height resistance is unsatisfied, replace the fuel sender as an assembly.
After completing this test, wipe the sender dry and reinstall it in the fuel tank.
Engine Coolant Temperature Gauge
1.
Disconnect the wiring connector (A) from the engine coolant temperature sender in the engine compartment.
2.
Turn the ignition switch ON. Check that the gauge needle indicates cool. Turn the ignition switch OFF.
3.
Connect a 12V, 3.4 watt test bulb between the harness side connector and ground.
4.
Turn the ignition switch ON.
5.
Verify that the test bulb flashes and that the indicator moves to HOT.
If operation is not as specified, replace the engine coolant temperature gauge. Then recheck the system.

Engine Coolant Temperature Sender
1.
Using an ohmmeter, measure the resistance between the terminal 2 and ground.
2.
If the resistance value is not as shown in the table, replace the temperature sender.
Temperature
[°F(°C)]
Gauge Segment
131(55)
SEG1
160(71)
SEG5
230(110)
SEG5
249.35(120.75)
SEG11
256.1(124.5)
SEG12

Brake Fluid Level Warning Switch
1.
Remove the connector (A) from the switch located at the brake fluid reservoir.
2.
Verify that continuity exists between switch terminals 1 and 2 while pressing the switch (float) down with a rod.

Brake Fluid Level Warning Lamp
1.
Ignition "ON"
2.
Release the parking brake.
3.
Remove the connector from the brake fluid level warning switch.
4.
Ground the connector at the harness side.
5.
Verify that the warning lamp lights.
Parking Brake Switch
The parking brake switch (A) is a pulling type. It is located under the parking brake lever. To adjust, move the switch mount up and down with the parking brake lever released all the way.
1.
Check that there is continuity between the terminal and switch body with the switch ON (Lever is pulled).
2.
Check that there is no continuity between the terminal and switch body with the switch OFF (Lever is released).
If continuity is not as specified, replace the switch or inspect its ground connection.

Door Switch
Remove the door switch and check for continuity between the terminals.

Seat Belt Switch
1.
Remove the connector from the switch.
2.
Check for continuity between terminals.
Seat belt condition
Continuity
Fastened
Non-conductive (∞Ω)
Not fastened
Conductive (Ω)

Seat Belt Warning Lamp
With the ignition switch turned ON, verify that the lamp glows.
Seat belt condition
Warning lamp
Fastened
OFF
Not fastened
ON


Removal

1.
Disconnect the negative (-) battery terminal.
2.
Tilt the steering column down.
3.
Remove the instrument cluster fascia lower panel (A).

4.
Remove the instrument cluster (A) after loosening the screws.

5.
Disconnect the cluster connector (A), then remove the cluster.


Installation

1.
Install the cluster to the cluster housing.
2.
Install the cluster fascia lower panel.

    Instrument Cluster. Schematic Diagrams
    Circuit Diagram Input/Output Specification ...

    Trip Switch. Schematic Diagrams
    Circuit Diagram ...

    See also:

    Repair procedures
    Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the driver crash pad lower panel. (Refer to the BD group - "Cra ...

    Headlight, position light, turn signal light, side marker light and front fog light bulb replacement
    (1) Headlight (High) (2) Headlight (Low) (3) Front turn signal light / Position light (4) Front fog light (if equipped) Headlight bulb WARNING - Halogen bulbs Halogen bulbs contain pr ...

    Preparation Of Tools And Measuring Equipment
    Be sure that all necessary tools and measuring equipment are available starting work. Special Tools Use special tools when they are required. Removal Of Parts First find th ...