Replacement
Front Seat Belt Replacement
•
|
When installing the belt, make sure not to damaged the
pretensioner.
|
|
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD group - "Front Seat")
|
B. |
Front and rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
|
2. |
Using a screwdriver or remover, remove the seat belt lower anchor
(A).
![](images/books/412/syfbd0178n.gif)
|
3. |
Remove the center pillar lower trim (A).
![](images/books/412/syfbd0179n.gif)
|
4. |
After loosening the mounting screws, then remove the center pillar
upper trim (A) .
![](images/books/412/syfbd0180l.gif)
|
5. |
After loosening the mounting bolt, then remove the upper anchor
(A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
![](images/books/412/syfbd0225d.gif)
|
6. |
After disconnecting the pretensioner connector lock pin, remove
the SIS connector (B), loosen the mounting bolt, then remove the pretensioner
(A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
![](images/books/412/syfbd0305n.gif)
|
7. |
Installation is the reverse of removal.
|
Height Adjust Replacement
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD gruop - "Front Seat")
|
B. |
Front and rear door scuff trim
(Refer to the BD gruop - "Interior Trim")
|
C. |
Front seat belt anchor
|
D. |
Center pillar lower trim
(Refer to the BD gruop - "Interior Trim")
|
E. |
Center pillar upper trim
(Refer to the BD gruop - "Interior Trim")
|
F. |
Front seat belt upper anchor
|
|
2. |
After loosening the bolts, then remove the hight adjustor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5kgf.m, 28.9 ~ 39.8 lb-ft)
|
![](images/books/412/syfbd0227d.gif)
|
3. |
Installation is the reverse of removal.
• |
Replace any damaged clips.
|
• |
Make sure the height adjust properly.
|
|
|
Front Seat Belt Buckle Replacement
1. |
Remove the front seat.
(Refer to the BD group - "Front Seat")
|
2. |
After loosening the mounting bolt, then remove the front seat
belt buckle (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
![](images/books/412/syfbd0228d.gif)
|
3. |
Installation is the reverse of removal.
|
Components
1. Front seat belt
2. Height adjuster
3. Rear seat belt (RH)
4. Rear center seat belt
5. Rear seat belt (LH)
6. Rear center seat belt buckle
...
Replacement
Rear Seat Belt Replacement
•
When installing the belt, make sure not to damaged the ...
See also:
Repair procedures
General Inspection
After or before servicing the EPS system, perform the troubleshooting
and test procedure as follows. Compare the system condition with normal condition
in the table below ...
Yaw-rate and Lateral G Sensor. Repair procedures
Removal
1.
Turn ignition switch OFF and disconnect the negative (-) battery
cable.
2.
Remove the floor console.
3.
...
Driver's and passenger's front air bag
Driver’s front air bag
Your vehicle is equipped with a Supplemental Restraint (Air Bag) System and lap/shoulder
belts at both the driver and passenger seating positions. The indications of th ...