Hyundai Sonata: Rear Hub - Carrier. Repair procedures - Rear Axle Assembly - Driveshaft and axleHyundai Sonata: Rear Hub - Carrier. Repair procedures

Replacement

1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).
3.
Loosen the mount screw and then brake disc (A).
Tightening torque:
4.9 ~ 6.8 N.m (0.5 ~ 0.7 kgf.m, 3.6 ~ 5.0 lb-ft)

4.
Loosen the rear upper arm and then remove the rear upper arm (A).
Tightening torque:
137.2 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.2 ~ 115.7 lb-ft)

5.
Remove the brake caliper mounting bolts , and then place the brake caliper assembly (B) with wire as shown in the illustration.
Tightening torque:
78.4 ~ 98.0 N.m (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

6.
Disconnect the wheel speed sensor connector (A).
Tightening torque:
6.8 ~ 10.7 N.m (0.7 ~ 1.1 kgf.m, 2.8 ~ 7.9 lb-ft)

7.
Disconnect the parking cable mouning clip (A), remove the parking cable (B).
8.
Loosen the trailing arm mounting bolt, and then remove the trailing arm (A).
Tightening torque:
44.1 ~ 53.9 N.m (4.5 ~ 5.5 kgf.m, 32.5 ~ 39.7 lb-ft)

9.
Loosen the assist arm mounting nut and then remove the assist arm (A).
10.
Loosen the lower arm (A) and rear strut (B) mounting bolts and remove the knuckle assembly (C).
Tightening torque:
Lower arm : 137.2 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.2~115.7 lb-ft)
Strut : 137.2 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.2 ~ 115.7 lb-ft)

11.
Loosen the hub bearing mounting, and then remove the hub bearing from knuckle (A).
Tightening torque:
78.4 ~ 88.2 N.m (8.0 ~ 9.0 kgf.m, 57.8 ~ 65.0 lb-ft)

12.
Install in the reverse order of removal.
13.
Check the alignment. (Refer to SSgroup 'Tires/Wheels - alingment')

Inspection

1.
Check the hub for cracks and the splines for wear.
2.
Check the brake disc for scoring and damage.
3.
Check the rear axle carrier for cracks.
4.
Check the bearing for cracks or damage.

    Rear Hub - Carrier. Components and Components Location
    Components 1. Rear Carrier Assembly 2. Parking Brake Assembly 3. Rear Hub Assembly 4. Rear Brake Disc ...

    See also:

    Warnings and indicators
    All warning lights are checked by turning the ignition switch ON (do not start the engine). Any light that does not illuminate should be checked by an authorized HYUNDAI dealer. After starting th ...

    Using the Room Mirror Key
    Selecting the room mirror key will allow you to make service required inquiries, POI info searches, and emergency rescues by connecting to the Blue Link Center. Such features can be used only after ...

    Vehicle data collection and event data recorders
    This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road ...